Shop Press

Shop Press is the news and idea hub for everything related to working on cars and trucks, focusing on repair, technology, and wrenching lifestyle.

From the creative minds at:

FEATURE STORY

Hot Off the Press

PSA: Hood, Trunk, and Rear Hatch Lift Supports Need Inspection, Too

The story goes that ol’ Isaac Newton took a knock to the head from a falling apple, leading to some bright ideas about gravity. While working on a vehicle, I recently bumped my dome and got a good idea, too, but this one’s for techs instead of physicists. So what...

The smarter way to check electrical connection contacts (VIDEO)

Description When it's time to check electrical connections, don't risk damaged components and unreliable test results with improvised equipment. Learn how properly sized test tools can take frustration out of the equation during electrical diagnostics. Related...

Real Vampire Bites? Technicians, Watch Out!

While investigating an intermittent headlight this week, I caught a glimpse of something that raised my hackles and had me reaching for my flashlight in a hurry. Lurking in the dark, behind the headlight housing, was that … a vampire tap? With a skinny black wire...

Five tips for servicing cartridge-style oil filters

by | Aug 8, 2023

The oil change is supposed to be simple, right? And while the service guide is always your guide, there are a few things that pertain to servicing vehicles equipped with cartridge-style oil filters that aren’t always covered as well as they could be. Here’s a few tips on servicing them correctly that should be helpful for newer techs and a good reminder for more experienced mechanics.

1

Remove the filter before draining the oil

This is especially true when dealing with filters located on top of the engine. They engage an anti-drainback valve when installed and draining the crankcase before removing the filter will allow the dirtiest oil in the engine right back into the crankcase! If not caught, it could result in an overfilled crankcase and will certainly contaminate any new, clean oil added.

Photo of used cartridge filter

Always drain and remove a cartridge-style filter prior to draining the pan. Photo: Peter F Meier.

2

Use the right tool for the job

Tongue-and-groove pliers are not designed to remove the oil filter caps on cartridge filters. Use the right tool for the job to avoid damage to the cap or housing assembly. The tool will differ based on the car, but be assured tongue-and-groove pliers are always the wrong item. A small crack in either will lead to a big bill later.

3

Inspect the housing and cap for damage

With the filter cap removed, gently remove the O-ring(s) from the cap and note their location(s). Do not use a tool to remove the O-ring from the threaded portion of the cap. Clean the housing and cap and inspect carefully for any signs of damage. If in doubt, replace it.

On some designs, and on all spin-on filter designs, the sealing O-ring may be left behind on the engine when the filter is removed. Verify the seal has been removed with the filter to avoid accidentally installing the new seal on top of the old. Two rubber seals don’t seal at all, and it will only be a matter of time before the oil pressure in the engine blows all the oil out onto the pavement.

Make sure the new filter has everything you need, including the O-rings. Inspect the O-rings for defect prior to use. Photo: Peter F Meier.

4

Pay attention to the details

Open the new filter package and compare the contents to the ones removed. Carefully inspect the new O-ring(s) for signs of damage. If any are noted, exchange the filter and its O-rings for a replacement.

And never reuse an O-ring! Lubricate the new O-ring(s) with clean motor oil. Gently roll the new cap O-ring down over the threads, making sure it is fully seated in its groove. Never attempt to stretch the O-ring over the cap. With the O-ring in place, install the remaining components into the cap and install in the housing. If you see that the O-ring is getting caught in the threads, do not attempt to use it—replace it.

5

Apply proper torque

Cartridge filter caps have specific torque specs. Using the proper tool and your torque wrench, tighten it to spec and complete your installation as outlined by the OEM procedure.

By following these tips when dealing with cartridge filters, you’re ensuring your shop delivers top-notch maintenance and best practices to your customers—exactly the reason they turn to you.

The articles and other content contained on this site may contain links to third party websites. By clicking them, you consent to Dorman’s Website Use Agreement.

Related Articles

Shop Press Comment Policy

Participation in this forum is subject to Dorman’s Website Terms & Conditions. Please read our Comment Policy before commenting.

Subscribe
Notify of
guest
0 Comments
Newest
Oldest Most Voted